Timepieces for the craftsman

Variety based on top technology. With our complete range of heating products, we are setting new standards and focusing on the economical use of energy. In each of our individual needs analyzes, we focus on cost-efficiency and environmental-friendly properties.

However, renewal is not always the only right choice, because even a skilled modernization can be worthwhile! Maximum comfort at affordable cost - according to this principle, we offer you the ideal components for your heating renovation.

How can you do the best? - we lead you on your way to modern living and warm water comfort and always have one in mind: efficiently used energy.

An old oil heater or an old gas boiler waste a part of the energy used unused. With a modern heating system, you can use the optimal energy yield from the very first hour and additionally ensure an environmentally friendly natural heat. Because much less CO2 emissions not only protect our environment, they are a promise to succeeding generations.

Condensing heaters with integrated solar, for example, achieve a reduction of up to 30 percent. The CO2 emissions can be reduced by approx. 50% by means of combined heat and power. Biomass heating systems are completely CO2-neutral and heat pumps operate completely without emissions.

Heating systems save a lot of money and they are much faster than expensive insulation or the exchange of all windows and doors. The investment costs of heating modernization or renovation are quickly amortized again. We offer you the best on the market with the best choice of the assortment of Viessmann, Wolf, HSK, Atmos, Danfoss, Reflex, Heimeier, Honeywell, Intercal, Orkli, Taconova, Wilo, Grundfos, Esbe, Suntec and EMK.

Whether oil pumps, heating regulators, valves, shut-off valves, buffer heaters or heat exchangers - our selection is large and consists of the best. Your heating system is repaired, renewed or modernized. Depending on your requirements, you will find in our shop all necessary parts and complete systems for the successful heating installation.

Start today and save on heating costs. At the latest on your next energy cost calculation, you will remember us with pleasure!
Old gas or oil heaters can be replaced within one to three days. After all, all the necessary components of our premium manufacturers are matched to one another and can be pre-assembled, simply matched to one another. After commissioning, our different components of the heating requirements work reliably, quietly and with little maintenance.

We like to save money - but not at all! That is why you only receive heating requirements at a top level.

Climate protection is promoted - with up to € 3,500 MAP funding including € 500 supplementary bonus (APEE - incentive program energy efficiency), as well as the possibility of a KfW subsidy (Energiesparverordnung) - you will also find the perfect energy saving system for your own home.

Various combinations offer you and your family a modern comfort. If you want to renew an oil heating system, switching to natural gas would be worthwhile if natural gas is available in your home. This solution is considered the cleanest of all fossil fuels. A combination of solar, condensing and gas technology also doubles as efficient and with a cogeneration system you will not only produce heat but also electricity.
No matter for which system you want to use our heating needs, energy and their efficient use is an important topic that will accompany us for a long time in times of energy certification, energy saving regulation and high electricity costs. We work with our premium manufacturers every day to make an environmentally friendly changeover to the different heating systems. Help us and start changing today - we are part of it!
TA Heimeier Eclipse valve key 3930-02-1482
10,43 EUR
incl. 19% tax excl. Shipping costs
Clamp ring screw connections for oil filter
Size clamp rings:
6mm ( +0,42 EUR )
8mm ( +0,42 EUR )
10mm
12mm
10,71 EUR
incl. 19% tax excl. Shipping costs
Afriso quick breather

Connection size:
DN 10 = 3/8"
DN 15 = 1/2" ( +0,51 EUR )
10,72 EUR
incl. 19% tax excl. Shipping costs
Splash guard 1/2 " for Heating
10,80 EUR
incl. 19% tax excl. Shipping costs
Loro-X safety clamp
Diameter:
DN 40 / 40mm
DN 50 / 50mm ( +0,51 EUR )
DN 70 / 75mm ( +7,18 EUR )
DN 100 / 110mm ( +12,21 EUR )
10,97 EUR
incl. 19% tax excl. Shipping costs
Sleeve racketeer from brass with internal thread
Connection size:
DN 15 = 1/2" ( +2,67 EUR )
DN 20 = 3/4" ( +2,87 EUR )
DN 25 = 1" ( +6,87 EUR )
DN 32 = 1 1/4" ( +9,03 EUR )
DN 40 = 1 1/2" ( +13,85 EUR )
DN 50 = 2" ( +22,77 EUR )
DN 10 = 3/8"
DN 65 = 2 1/2" ( +46,16 EUR )
DN 80 = 3" ( +55,91 EUR )
11,06 EUR
incl. 19% tax excl. Shipping costs
Clamp screw connections (art out of vision pipe) for cock's blocks
Connection size:
Pipe 12 x 2,0 mm
Pipe 14 x 2,0 mm
Pipe 16 x 2,0 mm
Pipe 16 x 2,2 mm
Pipe 17 x 2,0 mm
Rohr 17 x 2,5 mm
11,12 EUR
incl. 19% tax excl. Shipping costs
FAL waste gas pipe, length 250 mms
Diameter / connection size:
DN 60 = 60mm
DN 180 = 180mm ( +4,27 EUR )
DN 160 = 160mm ( +3,05 EUR )
DN 150 = 150mm ( +2,20 EUR )
DN 130 = 130mm ( +1,22 EUR )
DN 120 = 120mm ( +0,85 EUR )
DN 110 = 110mm ( +0,85 EUR )
DN 100 = 100mm ( +0,85 EUR )
DN 90 = 90mm ( +0,85 EUR )
DN 80 = 80mm ( +0,61 EUR )
DN 70 = 70mm ( +0,37 EUR )
DN 200 = 200mm ( +6,71 EUR )
11,27 EUR
incl. 19% tax excl. Shipping costs
Ball cocks with short red T-handle an Female Therad

Connection size:
DN 10 = 3/8"
DN 15 = 1/2" ( +1,23 EUR )
DN 20 = 3/4" ( +2,56 EUR )
DN 25 = 1" ( +5,95 EUR )
DN 32 = 1 1/4" ( +12,82 EUR )
11,27 EUR
incl. 19% tax excl. Shipping costs
Ball cocks with short red T-handle an external thread

Connection size:
DN 15 = 1/2"
DN 20 = 3/4" ( +2,56 EUR )
DN 25 = 1" ( +5,95 EUR )
DN 32 = 1 1/4" ( +12,82 EUR )
11,27 EUR
incl. 19% tax excl. Shipping costs
Ball cocks with long red lever handle an external thread

Connection size:
DN 10 = 3/8"
DN 15 = 1/2"
DN 20 = 3/4" ( +2,56 EUR )
DN 25 = 1" ( +5,95 EUR )
DN 32 = 1 1/4" ( +12,82 EUR )
DN 40 = 1 1/2" ( +15,29 EUR )
DN 50 = 2" ( +22,06 EUR )
11,27 EUR
incl. 19% tax excl. Shipping costs
Ball cocks with long red lever handle an internal thread

Connection size:
DN 10 = 3/8"
DN 15 = 1/2"
DN 20 = 3/4" ( +2,56 EUR )
DN 25 = 1" ( +5,95 EUR )
DN 32 = 1 1/4" ( +12,82 EUR )
DN 40 = 1 1/2" ( +15,29 EUR )
DN 50 = 2" ( +22,06 EUR )
DN 65 = 2 1/2" ( +36,83 EUR )
DN 80 = 3" ( +48,73 EUR )
11,27 EUR
incl. 19% tax excl. Shipping costs
Clamp ring screw 3/4" connection for PE-pipe
Pipe size:
12 x 2,0 mm ( +0,61 EUR )
14 x 2,0 mm
16 x 2,0 mm
17 x 2,0 mm
18 x 2,0 mm
20 x 2,0 mm ( +0,61 EUR )
11,34 EUR
incl. 19% tax excl. Shipping costs
Danfoss corner adaptor
11,73 EUR
incl. 19% tax excl. Shipping costs
Danfoss corner adaptor M30 x 1,5mm

11,73 EUR
incl. 19% tax excl. Shipping costs
Esbe screw connection part for valves with external thread
Screw connection for valve:
DN 15 = 1/2 ( +3,30 EUR )
DN 20 = 3/4"
DN 25 = 1" ( +0,98 EUR )
DN 32 = 1 1/4" ( +5,25 EUR )
DN 40 = 1 1/2" ( +8,55 EUR )
DN 50 = 2" ( +15,87 EUR )
11,99 EUR
incl. 19% tax excl. Shipping costs
Loro-X Glue 125g
12,02 EUR
incl. 19% tax excl. Shipping costs
MTR Quick breather
12,07 EUR
incl. 19% tax excl. Shipping costs
Loro-X with two sleeve DN 50 in different lengths
Pipe length:
0,25 m
0,50 m ( +5,33 EUR )
0,75 m ( +9,34 EUR )
1,00 m ( +13,54 EUR )
2,00 m ( +53,90 EUR )
12,18 EUR
incl. 19% tax excl. Shipping costs
Splash guard 1/2 " for warm amounts counter
13,11 EUR
incl. 19% tax excl. Shipping costs
Splash guard 3/4 " for Heating
13,25 EUR
incl. 19% tax excl. Shipping costs
FAL waste gas pipe, length 500 mms
Diameter / connection size:
DN 60 = 60mm
DN 180 = 180mm ( +3,66 EUR )
DN 160 = 160mm ( +2,44 EUR )
DN 150 = 150mm ( +1,95 EUR )
DN 130 = 130mm ( +1,71 EUR )
DN 120 = 120mm ( +1,22 EUR )
DN 110 = 110mm ( +0,98 EUR )
DN 100 = 100mm ( +0,85 EUR )
DN 90 = 90mm ( +0,85 EUR )
DN 80 = 80mm ( +0,61 EUR )
DN 70 = 70mm ( +0,37 EUR )
DN 200 = 200mm ( +6,10 EUR )
13,52 EUR
incl. 19% tax excl. Shipping costs
Stuffing box for valve case RAV, RAVL, RA-KE, RA K and FJVR 013U0070
13,60 EUR
incl. 19% tax excl. Shipping costs
Pipe feather of pressure manometers in executions passed away

Connection size:
DN 15 = 1/2" ( +6,10 EUR )
DN 10 = 3/8"
DN 8 = 1/4"
Measuring area:
0-2,5 bar
0-6 bar
0-10 bar ( +0,61 EUR )
0-16 bar ( +0,98 EUR )
0-25 bar ( +1,22 EUR )
0-40 bar ( +1,83 EUR )
Thread connection:
Behind/axially
Below/radial
13,83 EUR
incl. 19% tax excl. Shipping costs
Screwing straight through pattern for plate heat exchangers
Connection size:
DN 20 = 3/4"
DN 25 = 1" ( +6,67 EUR )
DN 32 = 1 1/4" ( +16,93 EUR )
13,90 EUR
incl. 19% tax excl. Shipping costs
37 to 72 (from a total of 1695)